Tel: +49 (0) 8432 / 87-0

Customised soft-impact surfaces from Polytan:

Polytan_Kästner_Schule_01-scaled

Thanks to their shock-absorbing effect, soft-impact surfaces help prevent severe (head) injuries. They are traditionally installed in educational institutions such as nurseries and schools as well as in children’s play areas. Other locations include rehabilitation centres, leisure parks, retirement homes, outdoor gyms, swimming-pools and hotel facilities. Soft-impact products exist in the form of loose bulk material such as sand and gravel or as synthetic panels, seamless synthetic systems and synthetic turf. Polytan, the world’s leading manufacturer of sports surfaces for outdoor use, offers high-grade soft-impact surfaces in two forms: as a seamless synthetic surface, Polytan FS, and with a synthetic turf finish in the Polytan FS Nature and Polytan FS Play versions.

While weather and rot-resistant synthetic soft-impact surfaces are a little more expensive to buy than traditional bulk material, the costs of acquisition pay off after only a few years. That’s because – unlike sand, cork or bark mulch – the only cleaning that is required is for the surface, not deeper contamination, and there is no need to keep refilling areas that wear out quickly, such as the landing area of a slide. What is more, bulk materials can tend to lose some or even all of their shock-absorbing effect when wet.

That makes weather and rot-resistant synthetic surfaces much more hygienic, while the smooth surface also allows easy access for wheelchair users. (Point) loads caused by children on stilts, for instance, will not make any lasting impact either. To ensure a long life of more than ten years, Polytan recommends regular intensive wet cleaning every two to three years. Shaded areas will get dirtier much more quickly than areas that are exposed to sunlight and free of leaves. Optimum long-term maintenance is in any case guaranteed with the manufacturer’s care plan.

Polytan FS soft-impact surface – for smooth, seamless shock absorption

 
To give planners and architects the greatest possible creative freedom, the water-permeable Polytan FS soft-impact surface is available in 24 standard colours and more than twice as many special colours. Colour adjustments are also possible, such as if a club or school crest is to be adapted. The surface can be installed not only on level but also on bumpy ground and slopes. The product generally consists of two layers: the top layer is 15 mm thick and manufactured from high-grade, completely newly produced EPDM granules (rubber). The necessary elasticity is provided by the second, absorbent layer made of recycled material. The thickness of the base layer varies between 30 and 115 mm, depending on the critical fall height of the play equipment. Soft-impact surfaces are appropriate up to a fall height of 3 m, above which the law requires railings.

The soft-impact surface is installed directly on site in a seamless in-situ process. The 2-8 mm rubber granules for the base layer and the 1-3.5 mm EPDM granules for the top layer are encased with a PU binder and bonded together. This in-situ installation allows the surface to adapt to all corners, edges and unevenness in the ground. The surface is sufficiently hard to be walked on after about 24 hours. Its water permeability depends on the chosen layer thicknesses, but is far above the requirements set out in DIN EN 14877 "Synthetic surfaces for outdoor sports areas".

Polytan FS conforms to fire safety class Bfl – s1 for flooring, so is classed as hardly flammable. The surface can easily withstand great heat up to and over 100 °C, while the impact noise properties and sound insulation can be regarded as generally positive.

Polytan FS Nature and FS Play – fall protection combined with synthetic turf

 
It was at the 2015 International Trade Fair for Amenity Areas, Sports and Pool Facilities (FSB) that Polytan first presented its new Polytan FS Nature and Polytan FS Play soft-impact surfaces. What is unusual about them is that they combine the attributes of two product worlds: shock-absorbing surfaces and textured (crimped) synthetic turfs.
The soft-impact surfaces consist of a thick, elastic base layer and a synthetic turf filled with quartz sand. As with the seamless Polytan FS soft-impact surface, the thickness of the elastic layer depends on the critical fall height of the play equipment.
The look of FS Nature comes very close to that of natural turf, as the filaments (stalks) are composed of light and dark green fibres. With green or blue synthetic turf surfaces and colour inlays in the form of graphics or hopscotch, Polytan FS Play offers additional scope for design freedom. The CoolPlus function, which reflects sunlight, helps to protect the surface of the turf from overheating in the summer.

Legal requirements on soft-impact surfaces

 
The requirements on soft-impact surfaces are essentially laid down in the European DIN EN 1176 "Playground equipment" and DIN EN 1177 "Impact attenuating playground surfacing" standards. These standards specify that impact attenuating surfaces must always be installed below play equipment from a free fall height of 60 cm and under equipment that causes a forced motion (e.g. see-saws and rocking items). How much safety a soft-impact product offers is indicated by its HIC value. HIC stands for Head Injury Criterion and is an indicator of the severity of head injuries. In the case of soft-impact materials in children’s play areas, the maximum HIC reading of 1000 ensures that no head injuries with permanent consequences are caused through falls. It is to be regarded as equivalent to the critical fall height. The lower the HIC reading, the better the head of the falling child is protected. Every soft-impact surface must be tested by an independent test institution in compliance with DIN 1177. The manufacturer should also have an independent test institution verify whether certified product systems are used. This can be ensured through evidence of quality, such as the RAL 943/3 quality mark.

A further legal requirement to be considered when planning is the German "GUV-SR 2002 – Guidelines for kindergartens – Construction and equipment".

Share / Subscribe

You might also like

Polytan LigaTurf Cross GT zero on the training grounds of Bayer 04 Leverkusen
An impressive sustainability concept Leverkusen is known for the Bayer Group and the closely associated Bundesliga football club Bayer 04, which represents attractive top-level football in Germany. The club remains a full subsidiary of the Bayer Group, for which, as in Wolfsburg, an exception to the 50+1 rule applies. Owing to its continued close association […]
Polytan and MakinH announce strategic partnership
Dry hockey as the goal German sports flooring manufacturer Polytan and Belgian sporting goods manufacturer MakinH are entering into a strategic partnership with one goal, which is to develop solutions for the current issue facing the hockey industry: dry hockey. Both companies are represented at this year’s FSB and will present their partnership for the […]
Experience the entire world of sport
Polytan at FSB 2023, 24th–27th October in Cologne   In 2023, Polytan will once again make an appearance at the International Trade Fair of Amenity Areas, Sports and Pool Facilities (FSB) in Cologne. This year, German specialist for synthetic turf and sports surfaces will present itself under the slogan: “Sport. People. Greener.” It underlines the […]
We Make
Sport.
Subscribe to newsletter

Newsletter Subscription

Newsletter Anmeldung (EN)

When registering for the newsletter, your email address will be processed for our own advertising purposes until you unsubscribe from the newsletter. You can unsubscribe at any time. With consent, the data you provide will be processed by Polytan GmbH for the purpose of sending the newsletter. Information about your right of withdrawal and how we handle your data can be found in our data protection information.

* = Mandatory fields